77-80 900ss fairing
7 posts
• Page 1 of 1
77-80 900ss fairing
Does someone have one of these? I would like to know how wide the rear section of the fairing is. I am thinking about putting one on my naked Paso.
Prince George BC
907ie
907ie
-
handbasket - Posts: 12
- Joined: Sun Jan 31, 2010 6:11 pm
Re: 77-80 900ss fairing
Hi handbasket:
I have one off a custom bike.
It was on a bevelhead 860GT.
It is correct for a sport or supersport 750 or 900.
$250 and it is yours if you'd like it.
It is painted red.
It has the round hole for the headlight. That is the one where the headlight has to be fairing mounted.
I have one off a custom bike.
It was on a bevelhead 860GT.
It is correct for a sport or supersport 750 or 900.
$250 and it is yours if you'd like it.
It is painted red.
It has the round hole for the headlight. That is the one where the headlight has to be fairing mounted.
Peter in Red Bay, Ontario.
1975 Ducati 750 GT lightly customised
1975 Ducati 860 GT custom project
2004 Multistrada 1000DS
1975 Ducati 750 GT lightly customised
1975 Ducati 860 GT custom project
2004 Multistrada 1000DS
- bevelheadpeegee
- Posts: 16
- Joined: Thu May 12, 2005 9:45 am
- Location: Red Bay on the Bruce Peninsula On
Re: 77-80 900ss fairing
These guys make new ones for $172. I like the idea on getting a headlight deleted fairing and installing some small projector lights. Do you have a windshield too? Mostly, I'm worried the fairing isn't wide enough to fit around the tank.
http://www.airtech-streamlining.com/duc ... .htm#price
http://www.airtech-streamlining.com/duc ... .htm#price
Prince George BC
907ie
907ie
-
handbasket - Posts: 12
- Joined: Sun Jan 31, 2010 6:11 pm
Re: 77-80 900ss fairing
Hi Handbasket:
I don't think I have a windshield for you.
I have one here, but I think I need it for my next project.
If you are looking to do the bike with projector/modern type lights. get the one from airtech with no holes and drill the holes with a hole saw yourself.
Send us a picture when it is all done, Eh?
I don't think I have a windshield for you.
I have one here, but I think I need it for my next project.
If you are looking to do the bike with projector/modern type lights. get the one from airtech with no holes and drill the holes with a hole saw yourself.
Send us a picture when it is all done, Eh?
Peter in Red Bay, Ontario.
1975 Ducati 750 GT lightly customised
1975 Ducati 860 GT custom project
2004 Multistrada 1000DS
1975 Ducati 750 GT lightly customised
1975 Ducati 860 GT custom project
2004 Multistrada 1000DS
- bevelheadpeegee
- Posts: 16
- Joined: Thu May 12, 2005 9:45 am
- Location: Red Bay on the Bruce Peninsula On
Re: 77-80 900ss fairing
7 inches wide at the narrowest point (lower part of the fairing wraps around behind the forks). 13 inches wide at the part closest to the rider. Original lower fairing mount is 19 inches wide, but bolts on part way up the fairing.
Can't remember how wide the Paso tank is but I very much doubt it will fit.....
Can't remember how wide the Paso tank is but I very much doubt it will fit.....
Mark
- markk900
- Posts: 55
- Joined: Sun Feb 18, 2007 9:13 am
Re: 77-80 900ss fairing
Still looking for bevel fairing? I have an original and have replicated it both with headlight opening and without, and can generaly make the width suitable to the bike. The original was posssibly off an early 750 Sport with a plexi covered lorger HL opening, as the headlight was fork mounted. It is essential to have a dash panel to prevent the reflected light. I make this one off stuff for myself and others, like replica 900 side covers, narrow case single sump oil pan, fitting above the exhaust, replica 916 race tail and fairing....netdavejones@netscape.net for price and availability.
- davejones
- Posts: 2
- Joined: Sun Dec 05, 2010 11:18 am
7 posts
• Page 1 of 1
Who is online
Users browsing this forum: No registered users and 6 guests