Ducati Owners Club Of Canada

916 crank shaft

Discuss maintenance and modification of modern Ducatis'.
13 posts • Page 1 of 1

916 crank shaft

Postby robb916998 » Sat Jul 07, 2012 5:02 pm

Ok funny story , I think the clutch is sorted as the push rod is still in one piece. BUT it only had like 10 laps befor the bike made a noise and quit .

SO can any one explain to me how the end of the crank shaft were the rotor and fly wheel are mounted can just up and BRAKE OFF ???

:evil: :shock: :evil: :shock: :evil: :shock:
hi
User avatar
robb916998
 
Posts: 700
Joined: Tue Jun 06, 2006 12:30 pm
Location: woodstock,canada

Re: 916 crank shaft

Postby robb916998 » Sat Jul 07, 2012 5:06 pm

sorry !
Yes i know I'm ridding a Ducati
:lol:
hi
User avatar
robb916998
 
Posts: 700
Joined: Tue Jun 06, 2006 12:30 pm
Location: woodstock,canada

Re: 916 crank shaft

Postby ERIC SUMMERS » Mon Jul 09, 2012 12:05 pm

Hello Robb,
gravity?
Tnxs. Eric
User avatar
ERIC SUMMERS
 
Posts: 270
Joined: Wed Mar 02, 2005 10:48 am
Location: Over the hill and far away.

916 crank shaft

Postby Dunlop » Mon Jul 09, 2012 1:30 pm

2008 Husqvarna SM610ie
2002 Ducati 998 monoposto (for $ale)
User avatar
Dunlop
 
Posts: 16
Joined: Mon Dec 12, 2011 11:44 am
Location: St. Augustine, FL, USA 32095

Re: 916 crank shaft

Postby robb916998 » Mon Jul 09, 2012 6:14 pm

Ya I over rev it !
Typically i knock it down a gear befor the corner and let it rev up coming into it .make that compression work for me, then it is usually in its happy place for the drive out . perhaps i need to re evaluate this.
it sees 11k on a regular Base.as it is chipped i was told it could do 11k. again a re think is in order!


GRAVITY SUCKS :lol:
hi
User avatar
robb916998
 
Posts: 700
Joined: Tue Jun 06, 2006 12:30 pm
Location: woodstock,canada

Re: 916 crank shaft

Postby huit » Mon Jul 09, 2012 6:28 pm

I don't think you are making any power up at
11. I would really think you want to keep it
In the fat part of the torque between 7/10.
Short shifting rather than over revving!
I have never seen or heard of it on a street bike
But the factory boys had broken a few in the early days
Hopefully it didn't do a lot of other damage!
Good luck with you repair!
Paul
huit
 
Posts: 102
Joined: Thu Dec 16, 2004 8:45 pm
Location: toronto

Re: 916 crank shaft

Postby robb916998 » Tue Jul 17, 2012 5:57 pm

okay ,motor out and cases are split !

Interesting thing ,this motor has gaskets ! case half's ,side case covers all have paper gaskets .
First one I have had apart with gaskets . so ?? do i put gaskets back in or just go with sealer ??
hi
User avatar
robb916998
 
Posts: 700
Joined: Tue Jun 06, 2006 12:30 pm
Location: woodstock,canada

Re: 916 crank shaft

Postby huit » Tue Jul 17, 2012 8:40 pm

Rob, early motors used gaskets, just use sealer.
You will have to re shim all the transmission and crank
Best to replace all bearings, not real cheap. But worth it.
Make sure you get the new style head gaskets
All metal and thinner.
I have a bunch of shims if you need any.
I also have a lightened 916 crank in good shape,
If you need one.
You can order a top end gasket kit that has everything you need!
Have fun with the rebuild!
huit
 
Posts: 102
Joined: Thu Dec 16, 2004 8:45 pm
Location: toronto

916 crank shaft

Postby Dunlop » Wed Aug 15, 2012 2:51 pm

2008 Husqvarna SM610ie
2002 Ducati 998 monoposto (for $ale)
User avatar
Dunlop
 
Posts: 16
Joined: Mon Dec 12, 2011 11:44 am
Location: St. Augustine, FL, USA 32095

Re: 916 crank shaft

Postby robb916998 » Sun Aug 19, 2012 9:26 pm

hi
User avatar
robb916998
 
Posts: 700
Joined: Tue Jun 06, 2006 12:30 pm
Location: woodstock,canada

Re: 916 crank shaft

Postby chris fournier » Mon Aug 20, 2012 10:22 am

Dunlop has told you what has lead to your broken engine. Revs kill engines. The more revs you use, the shorter the life of the engine. Reving an eBay engine with an unknown pedigree to 11 grand on a regular basis is going to end up much like your story! Now if you have a carefully prepared engine built for track abuse then the life span would be longer but the cost of such an engine is very high - parts and labour.
chris fournier
 
Posts: 67
Joined: Sat Nov 18, 2006 2:53 pm
Location: Kitchener

Re: 916 crank shaft

Postby robb916998 » Tue Aug 21, 2012 5:38 pm

Thanks for the input guys !

The parts are starting to roll in now ,I'll take the winter to go over it .
hi
User avatar
robb916998
 
Posts: 700
Joined: Tue Jun 06, 2006 12:30 pm
Location: woodstock,canada

Re: 916 crank shaft

Postby robb916998 » Sun Oct 21, 2012 11:46 am

Has any one ever done or tried the 900ss crank conversion to a 916 ??

If so , what is the easiest way to maintain the squish, find 2mm shorter rods ? and is there any Ducati rods that would directly fit in and do the job ? or is it corrillo's web site i need to be looking at ??

another option i am looking at is wiseco and having slugs made .

any thoughts or experiences would be appreciated!

thanx
hi
User avatar
robb916998
 
Posts: 700
Joined: Tue Jun 06, 2006 12:30 pm
Location: woodstock,canada


13 posts • Page 1 of 1

Return to modern ducati tech

Who is online

Users browsing this forum: No registered users and 6 guests

Powered by phpBB® Forum Software © phpBB Group Change colors.

Style designed by Artodia.